Machine wash cold.
Hang to dry.
Cool iron if needed.
Do not bleach.
Professional leather cleaning only.
Never use any solvents or abrasive cleaners to clean your helmet!! For optimum performance, rinse your helmet in warm water using a mild soap. If the outside is dirty with dried dirt and bugs, we suggest you place a wet towel over the helmet for at least one minute before wiping it clean. This softens the foreign objects before removal lessening the chance of scratches. Plastic polishes like Plexus or Honda polish will work fine to restore luster to your helmet as long as the dirt, grime and bugs have not been "scraped off" dry.
The multiple coatings on the face shield are resistant to light scratching, however, heavy, abusive scratching can break through the coatings and cause visible marks. Removing dirt and bugs with good cleaning practices and keeping your helmet in a RaceCase™ will significantly help to prolong the life of your helmet and face shields.
The removable, washable liner in all our helmets make it easy to clean. Even a man can do it. Remove the cheek pads first by unsnapping the 3 (usually) button snaps on each one. Be careful not to "tear" the pad out, but carefully un-snap each button. The "crownliner" can be unsnapped (2) from the back of the head area and the pulled away from the helmet in the forehead area. Note the alignment arrows for re-installing the crownliner. Throw these three pieces into the washing machine and allow to air dry before re-installing.
The ScorpionExo® face shields have different cleaning procedures for inside and outside. The outside is coated with an anti-scratch coating which prevents minor scratches, but cannot resist heavy wiping and cleaning without preliminary softening of the dirt, grime and bugs first. Note the damp towel method of softening dried bugs and dirt above. Plastic polishes work fine (clear and smoke shields only) to clean the outside of the shield as long as the dirt and grime has been softened and removed first. The inner Everclear® no-fog coated face shields required special treatment for cleaning. We suggest using a warm water and mild soap combination followed by "pat drying" with a dry towel. "Wiping" may cause premature wear and scratching on the Everclear® innercoating. Mirrored shields should use warm water only.
Certain common household chemicals will react negatively with the polycarbonates, fiberglass or coatings of your helmet. Avoid contact with acetone (nail polish remover), caustic solutions (ammonia-based cleaners), hair sprays containing methyene, chlorine from swimming pools or glues.
Scorpion Sports offers special low-cost repairs or replacement parts to keep your helmet in excellent working condition. Please give us or your local dealer a call. Our warranty and repair department can be reached Pacific Coast business hours at 1-888-212-0688.
Place your helmet into a suitably protected box and send via FedEx, USPS, or UPS, registered or insured to;
Scorpion Sports Inc.
ATTN: Warranty Dept.
10425 Slusher Drive
Santa Fe Springs, CA 90670
Scorpion EXOWear™ is warranted against defects in materials and workmanship for 5 years on Leather, 3 years on Textile, 1 year on Mesh products, 1 year on Covert Jeans/Flannels, and 1 year on gloves from original date of purchase, this warranty is limited to the repair and/or replacement of parts and the necessary labor and services required to repair the item. Normal wear and tear is not covered by this warranty.
Scorpion helmets are warranted against defects in materials and workmanship. Please see chart below for model and warranty period. Faceshields are warranted for 1 year from original purchase date, this warranty is limited to the repair and replacement of parts and the necessary labor and services required to repair the helmet. Normal wear and tear is not covered by this warranty.
HELMET WARRANTY CHART
3 YEAR PURCHASE / 5 YEAR MANUFACTURE DATE
5 YEAR PURCHASE / 7 YEAR MANUFACTURE DATE
The product may be returned directly to Scorpion Sports, Inc. Warranty Dept. for inspection (freight prepaid) Requests for Return Authorizations (RMA) should be requested via telephone at (888) 672-6774 or email email@example.com If the exact model of helmet in question is discontinued or no longer available, a model of equal or better value will be offered at the discretion of Scorpion Sports, Inc.
Canadian customers, please contact the dealer that you purchased your product from for a streamlined process. Thank You.
Modification of any kind made to the helmet by the user or any third party will render this warranty null and void. This includes but is not limited to the installation of audio systems, drilling the shell or liner, carving or compressing the liner and painting of the shell. Normal wear and tear to the finished and painted surfaces, abnormal treatment or abuse to the helmet interior is NOT covered under this warranty. This warranty also does NOT cover chips, scratches, abrasions or other damage to the helmet's outer shell, painted surfaces, and faceshield caused by contact with another surface or object
*IMPORTANT NOTE: All dyed/pigmented fabrics, polycarbonites (ie: helmets) and vinyl will fade under UV exposure (sunlight) over time. Scorpion fabrics are highly UV resistant, but HI-VIS fabrics will fade at a faster rate than normal fabrics under the same UV exposure. This is a normal property of all HI-VIS pigments/fabrics and is not considered a manufacturer defect.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SCORPION SPORTS, INC. SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
The first step in the fitting process is to measure around your head at the temple above the eye brow. See the placement of the measuring tape
|Size||Circumference Inches||Circumference CM||Hat size|
|XS||20 7⁄8 - 21 1⁄4||53-54 cm||6 5⁄8 - 6 3⁄4|
|SM||21 5⁄8 - 22||55-56 cm||6 7⁄8 - 7|
|MD||22 7⁄16 - 22 3⁄4||57-58 cm||7 1⁄8 - 7 1⁄4|
|LG||23 1⁄8 - 23 5⁄8||59-60 cm||7 3⁄8 - 7 1⁄2|
|XL||24 - 24 3⁄8||61-62 cm||7 5⁄8 - 7 3⁄4|
|2XL||24 3⁄4 - 25 3⁄16||63-64 cm||7 7⁄8 - 8|
|3XL||25 9⁄16 - 26||65-66 cm||8 1⁄8 - 8 1⁄4|
|Size||Circumference Inches||Circumference CM||Hat size|
|Y-SM||18 7⁄8 - 19 1⁄4||48-49 cm||Y-SM|
|Y-MD||19 3⁄4 - 20 1⁄4||50-51 cm||Y-MD|
|Y-LG||20 1⁄2 - 20 7⁄8||52-53 cm||Y-LG|
The next step in the fitment process are fitment checks. The following tests should be performed with the chin strap properly and securely in place. Helmet movement should also move the skin on your face and scalp. Helmets will fit snug when new and have a break in period. The helmet should not fit so tight as to cause discomfort or pain. If your measurement is at the upper number of any size range start at that range then move up as needed.
1. With the helmet in place and chin strap secured, shake your head side to side, if the helmet moves independently of your head then the helmet is too big. When performing this test, the helmet liner and cheek pads should be in direct contact with your skin. While shaking, your skin should move with the helmet.
2. Place one hand directly behind your head and push forward. Use your other hand and try to slip your little finger between your forehead and the helmet EPS liner. If you are able to slip your finger in, the helmet is too big.
3. To test for helmet lift, place one hand on the chin bar and push up (while the chin strap is secured), if the helmet comes off your head it is too big. Next, place one hand on the back and push up again, if your helmet lifts off your head the helmet is too big.
The first step in the fitting process is to measure around your chest then from your neck to wrist. For Gloves measure around your palm with your fingers open and spread. These are guidelines, a starting point.
|Chest||34 - 36||36 - 38||38 - 40||42 - 44||44 - 46||46 - 48||48 - 50|
|Tall Size||34 - 36||35 - 37||36 - 38||37 - 39|
|US 38 - Euro 48||38-39||32-33.5||31|
|US 40 - Euro 50||40-41||34-35||32|
|US 42 - Euro 52||42-43||35.5-36.5||32|
|US 44 - Euro 54||44-45||37-38||33|
|US 46 - Euro 56||46-47||38.5-39.5||33|
|US 48 - Euro 58||48-49||40-41||34|
|US 50 - Euro 60||50-51||41.5-42.5||34|
|Savanah & Haley *Low Rise*||XS||S||M||L||XL||XXL|
|Hellina / Jewel / Empire||XS||S||M||L||XL||2XL|
For over 10 years, ScorpionExo® has been DEDICATED to offering high quality, innovative motorcycle helmets and apparel at an incredible value. Some of the world’s best helmet and apparel designers spend countless hours developing and testing ScorpionExo® products to ensure that each and every ScorpionExo® HELMET AND GARMENT will surpass user expectations. Pulling R&D from some of the top riders in the world, from MotoGP™ all the way to the Dakar Rally, ScorpionExo® is committed to listening to your needs as a rider.
This formula is supported by Scorpion’s unique position in the manufacturing process: owning and operating our own state-of-the-art manufacturing facilities. Our development and manufacturing expertise provide the ScorpionExo® brand a level of quality and attention to detail that cannot be surpassed. ScorpionExo® is DEDICATED to making helmets and apparel that maximize comfort and safety through a variety of riding styles and conditions...and we are proud to stand behind every product we make.
At ScorpionExo® we are DEDICATED to providing premium quality safety products you can rely on, we live for our brand from start to finish and we ride the same streets as you do. ScorpionExo®... We are more than just a logo.